In FE model updating, as in any identification procedure, we select some parameters in the model, and try to fine-tune them to minimize the discrepancy between the model predictions and the measured data. The paper compares the performance of the generic element matrices, recently introduced by the authors, with other selection strategies for finite element model updating. The updated models obtained from these methods are compared with the measured data and rated according to their ability to produce the measured data within and beyond the frequency range used in the updating, and more importantly, according to their ability to predict the effect of design changes.

Issue Section:
Research Papers
Topics:
Finite element model, Design
1.
Ahmadian, H., Gladwell, G. M. L., and Ismail, F., 1994, “Families of Finite Element Models for Updating Procedures,” Proceedings, 12th International Modal Analysis Conference, also submitted to The International Journal of Analytical and Experimental Modal Analysis.
2.
Ahmadian, H., 1994, “Finite Element Model Updating Using Modal Testing Data,” Ph.D. Thesis, Department of Mechanical Engineering, University of Waterloo, Canada.
3.
Baruch
M.
, and
Bar Itzhack
Y.
,
1978
, “
Optimal Weighted Orthogonalization of Measured Modes
,”
AIAA Journal
, Vol.
16
, No.
4
, pp.
346
–
351
.
4.
Baruch
M.
,
1984
, “
Methods of Reference Basis for Identification of Linear Dynamic Structures
,”
AIAA Journal
, Vol.
22
, No.
4
, pp.
561
–
563
.
5.
Berman
A.
,
1979
, “
Mass Matrix Correction Using an Incomplete Set of Measured Models
,”
AIAA Journal
, Vol.
17
, No.
10
, pp.
1147
–
1148
.
6.
Berman
A.
, and
Nagy
E. J.
,
1983
, “
Improvement of a Large Analytical Model Using Modal Test Data
,”
AIAA Journal
, Vol.
21
, No.
8
, pp.
1168
–
1173
.
7.
Caesar
B.
, and
Peter
J.
,
1987
, “
Direct Updating of Dynamic Mathematical Models from Modal Testing Data
,”
AIAA Journal
, Vol.
25
, No.
11
, pp.
1494
–
1499
.
8.
Chen
J. C.
, and
Graba
J. A.
,
1980
, “
Analytical Model Improvement Using Modal Testing Results
,”
AIAA Journal
, Vol.
25
, No.
11
, pp.
1494
–
1499
.
9.
Gladwell
G. M. L.
, and
Ahmadian
H.
,
1996
, “
Generic Element Matrices for Finite Element Model Updating
,”
Mechanical Systems and Signal Processing
, Vol.
9
, pp.
601
–
614
.
10.
Golub, G. H., and Van Loan, C. F., 1991, Matrix Computations, Second edition. The Johnes Hopkins University Press, p. 582.
11.
Hall, B. M., Calkin, E. D., and Sholar, M. S., 1970, “Linear Estimation of Structural Parameters from Dynamic Test Data,” AIAA/ASME llth Structural Dynamics and Materials Conference, New York, pp. 193–197. 105–113.
12.
Hoff
C.
, and
Natke
H. G.
,
1989
, “
Correction of a Finite Element Model by Input-Output Measurements With Application to a Radar Tower
,”
The International Journal of Analytical and Experimental Modal Analysis
, Vol.
4
, No.
1
, pp.
1
–
7
.
13.
Kabe
A. M.
,
1985
, “
Stiffness Matrix Adjustment Using Mode Data
,”
AIAA Journal
, Vol.
23
, No.
9
, pp.
1431
–
1436
.
14.
Kammer
D. C.
,
1988
, “
Optimum Approximation for Residual Stiffness in Linear System Identification
,”
AIAA Journal
, Vol.
26
, No.
1
, pp.
104
–
112
.
15.
Lim
T. W.
,
1990
, “
Submatrix Approach to Stiffness Matrix Correction Using Modal Testing Data
,”
AIAA Journal
, Vol.
28
, No.
6
, pp.
1123
–
1130
.
16.
Nobari
A. S.
,
Robb
D. A.
, and
Ewins
D. J.
,
1993
, “
Model Updating and Joint Identification Methods: Applications, Restrictions and Overlap
,”
The International Journal of Analytical and Experimental Modal Analysis
, Vol.
8
, No.
2
, pp.
93
–
105
.
17.
O’Callahan, J. C., 1990, “Determination of Analytical Model Differences Using Modal Updating,” Proceedings, 8th International Modal Analysis Conference, Vol. 2, pp. 1180–1189.
18.
O’Callahan, J. C., and Wu, C. H., 1991, “System Identification and Localization Procedures With Structural Connectivity Constraint,” Proceedings, 9th International Modal Analysis Conference, Vol. 1, pp. 580–590.
19.
Ross, R. G., 1971, “Synthesis of Stiffness and Mass Matrix from Experimental Vibration Modes,” National Aeronautic and Space Engineering and Manufacturing Meeting, Society of Automotive Engineers, Los Angeles, CA, pp. 2627–2635.
20.
Smith
S. W.
, and
Beattie
C. A.
,
1991
, “
Secant-Method Adjustment for Structural Models
,”
AIAA Journal
, Vol.
29
, No.
1
, pp.
119
–
126
.
21.
Tlusty
J.
, and
Ismail
F.
,
1980
, “
Dynamic Structural Identification Tasks and Methods
,”
Annals of the CIRP
, Vol.
29
, pp.
251
–
255
.
22.
Wei
F.
,
1990
, “
Mass and Stiffness Interaction Effects in Analytical Model Modification
,”
AIAA Journal
, Vol.
28
, No.
9
, pp.
1686
–
1688
.
This content is only available via PDF.
Copyright © 1997
 by The American Society of Mechanical Engineers
You do not currently have access to this content.