Abstract

Fluid flow maldistribution causes deterioration of heat transfer as well as pressure drop penalty in heat exchangers. A test bench was set up to investigate the effect of different header designs on air-water flow distribution in plate-fin heat exchangers (PFHX). Two-phase flow distribution was examined for air Reynolds numbers (ReG) of 28293542 and inlet qualities (x) of 46.3–64.0%. Two-phase flow distribution was seen to be more uneven in the heat exchanger in comparison with single-phase flow, the water distribution being more uneven than that of the air. For a fixed inlet quality, as the air flowrate was increased, the distribution of two-phase flow became increasingly nonuniform, showing a pattern similar to single-phase flow. Furthermore, the air distribution became more even, while the water flow became more unevenly distributed as the inlet quality increased. To mitigate the maldistribution, perforated plates were incorporated in the heat exchanger header. The improved headers significantly aided in distributing the two-phase flow more evenly. At ReG = 2829 and x = 46.3%, the heat exchanger effectiveness was expressed in terms of the unevenness in quality, Sx. The effectiveness decreased as the unevenness of the flow distribution was exacerbated, emphasizing the significance of uniform phase and flow distribution as a key element of heat exchanger design.

References

1.
Wang
,
Z.
, and
Li
,
Y.
,
2016
, “
Layer Pattern Thermal Design and Optimization for Multistream Plate-Fin Heat Exchangers—A Review
,”
Renewable Sustainable Energy Rev.
,
53
(
53C
), pp.
500
514
. 10.1016/j.rser.2015.09.003
2.
Kakaç
,
S.
,
Pramuanjaroenkij
,
A.
, and
Liu
,
H.
,
2002
,
Heat Exchangers: Selection, Rating and Thermal Design
, 2nd ed.,
CRC Press
,
London, New York
.
3.
Tu
,
X. C.
,
Wu
,
Y. T.
, and
Kim
,
H. B.
,
2018
, “
Improvement of Two-Phase Flow Distribution in the Header of a Plate-fin Heat Exchanger
,”
Int. J. Heat. Mass Transfer
,
123
(
8
), pp.
523
533
. 10.1016/j.ijheatmasstransfer.2018.03.001
4.
Bhutta
,
M. M. A.
,
Hayat
,
N.
,
Bashir
,
M. H.
,
Khan
,
A. R.
,
Ahmad
,
K. N.
, and
Khan
,
S.
,
2012
, “
CFD Applications in Various Heat Exchangers Design: A Review
,”
Appl. Therm. Eng.
,
32
(
1
), pp.
1
12
. 10.1016/j.applthermaleng.2011.09.001
5.
Mueller
,
A. C.
,
1987
, “
Effects of Some Types of Maldistribution on the Performance of Heat Exchangers
,”
Heat Transfer Eng.
,
8
(
2
), pp.
75
86
. 10.1080/01457638708962795
6.
Ranganayakulu
,
C. H.
, and
Seetharamu
,
K. N.
,
1999
, “
The Combined Effects of Longitudinal Heat Conduction Flow Nonuniformity and Temperature Nonuniformity in Crossflow Plate-fin Heat Exchanger
,”
Int. Commun. Heat Mass
,
26
(
5
), pp.
669
678
. 10.1016/S0735-1933(99)00053-6
7.
Ranganayakulu
,
C. H.
, and
Seetharamu
,
K. N.
,
1999
, “
The Combined Effects of Wall Longitudinal Heat Conduction, Inlet Fluid Flow Nonuniformity and Temperature Nonuniformity in Compact Tube-fin Heat Exchangers: A Finite Element Method
,”
Int. J. Heat Mass Transfer
,
42
(
2
), pp.
263
273
. 10.1016/S0017-9310(98)00156-2
8.
Zhang
,
L. Z.
,
2009
, “
Flow Maldistribution and Thermal Performance Deterioration in a Cross-Flow Air to Air Heat Exchanger With Plate-fin Cores
,”
Int. J. Heat Mass Transfer
,
52
(
19–20
), pp.
4500
4509
. 10.1016/j.ijheatmasstransfer.2009.03.049
9.
Stevanovic
,
V.
,
Cucuz
,
S.
,
Carl-Meissner
,
W.
,
Maslovaric
,
B.
, and
Prica
,
S.
,
2012
, “
A Numerical Investigation of the Refrigerant Maldistribution From a Header Towards Parallel Channels in an Evaporator of Automotive Air Conditioning System
,”
Int. J. Heat Mass Transfer
,
55
(
13–14
), pp.
3335
3343
. 10.1016/j.ijheatmasstransfer.2012.02.071
10.
Jiao
,
A. J.
,
Li
,
Y. Z.
,
Chen
,
C. Z.
, and
Zhang
,
R.
,
2003
, “
Experimental Investigation on Fluid Flow Maldistribution in Plate-fin Heat Exchanger
,”
Heat Transfer Eng.
,
24
(
4
), pp.
25
31
.
11.
Jiao
,
A. J.
, and
Baek
,
S. W.
,
2005
, “
Effects of Distributor Configuration on Flow Maldistribution in Plate-fin Heat Exchangers
,”
Heat Transfer Eng.
,
26
(
4
), pp.
19
25
. 10.1080/01457630590916248
12.
Zhang
,
Z.
,
Mehendale
,
S.
,
Tian
,
J. J.
, and
Li
,
Y. Z.
,
2015
, “
Experimental Investigation of Distributor Configuration on Flow Maldistribution in Plate-fin Heat Exchangers
,”
Appl. Therm. Eng.
,
85
(
6
), pp.
111
123
. 10.1016/j.applthermaleng.2015.04.011
13.
Zhang
,
Z.
,
Li
,
Y. Z.
, and
Xu
,
Q.
,
2004
, “
Experimental Research on Effects of Distributor Configuration on Flow Distribution in Plate-fin Heat Exchangers
,”
Heat Transfer Asian Res.
,
33
(
6
), pp.
402
410
. 10.1002/htj.20023
14.
Jiao
,
A.
,
Zhang
,
R.
, and
Jeong
,
S.
,
2003
, “
Experimental Investigation of Header Configuration on Flow Maldistribution in Plate-fin Heat Exchanger
,”
Appl. Therm. Eng.
,
23
(
10
), pp.
1235
1246
. 10.1016/S1359-4311(03)00057-7
15.
Ismail
,
L. S.
,
Ranganayakulu
,
C.
, and
Shah
,
R. K.
,
2009
, “
Numerical Study of Flow Patterns of Compact Plate-fin Heat Exchanger Sand Generation of Design Data for Offset and Wavy Fins
,”
Int. J. Heat Mass Transfer
,
52
(
17–18
), pp.
3972
3983
. 10.1016/j.ijheatmasstransfer.2009.03.026
16.
Wen
,
J.
,
Li
,
Y.
,
Wang
,
S.
, and
Zhou
,
A.
,
2007
, “
Experimental Investigation of Header Configuration Improvement in Plate–fin Heat Exchanger
,”
Appl. Therm. Eng.
,
27
(
11–12
), pp.
1761
1770
. 10.1016/j.applthermaleng.2007.01.004
17.
Wen
,
J.
,
Li
,
Y.
,
Zhou
,
A.
, and
Zhang
,
K.
,
2006
, “
An Experimental and Numerical Investigation of Flow Patterns in the Entrance of Plate-fin Heat Exchanger
,”
Int. J. Heat Mass Transfer
,
49
(
9–10
), pp.
1667
1678
. 10.1016/j.ijheatmasstransfer.2005.10.029
18.
Wen
,
J.
,
Li
,
Y.
,
Zhou
,
A.
,
Zhang
,
K.
, and
Wang
,
J.
,
2006
, “
PIV Experimental Investigation of Entrance Configuration on Flow Maldistribution in Plate-fin Heat Exchanger
,”
Cryogenics
,
46
(
1
), pp.
37
48
. 10.1016/j.cryogenics.2005.10.010
19.
Wen
,
J.
, and
Li
,
Y.
,
2004
, “
Study of Flow Distribution and Its Improvement on the Header of Plate-fin Heat Exchanger
,”
Cryogenics
,
44
(
11
), pp.
823
831
. 10.1016/j.cryogenics.2004.04.009
20.
Zheng
,
W. K.
,
Jiang
,
Y. Q.
, and
Cai
,
W. H.
,
2019
, “
Distribution Characteristics of Gas-Liquid Mixture in Plate Fin Heat Exchangers Under Sloshing Conditions
,”
Exp. Therm. Fluid Sci.
,
101
(
1
), pp.
115
127
. 10.1016/j.expthermflusci.2018.09.019
21.
Zhu
,
J. L.
,
Zhang
,
W.
,
Li
,
Y. X.
,
Ji
,
P.
, and
Wang
,
W. C.
,
2019
, “
Experimental Study of Flow Distribution in Plate-fin Heat Exchanger and Its Influence on Natural Gas Liquefaction Performance
,”
Appl. Therm. Eng.
,
155
(
6
), pp.
398
417
. 10.1016/j.applthermaleng.2019.04.020
22.
Zhang
,
Z.
, and
Li
,
Y. Z.
,
2003
, “
CFD Simulation on Inlet Configuration of Plate-fin Heat Exchangers
,”
Cryogenics
,
43
(
12
), pp.
673
678
. 10.1016/S0011-2275(03)00179-6
23.
Wang
,
S.
,
Li
,
Y.
,
Wen
,
J.
, and
Ma
,
Y.
,
2010
, “
Experimental Investigation of Header Configuration on Two-Phase Flow Distribution in Plate-fin Heat Exchanger
,”
Int. Commun. Heat Mass
,
37
(
2
), pp.
116
120
. 10.1016/j.icheatmasstransfer.2009.07.014
24.
Yuan
,
P.
,
Jiang
,
G. B.
,
He
,
Y. L.
,
Yi
,
X. L.
, and
Tao
,
W. Q.
,
2013
, “
Experimental Study on the Performance of a Novel Structure for Two-Phase Flow Distribution in Parallel Vertical Channels
,”
Int. J. Multiphase Flow
,
53
(
7
), pp.
65
74
. 10.1016/j.ijmultiphaseflow.2012.05.006
25.
Al-Rawashdeh
,
M.
,
Nijhuis
,
T.
,
Rebrov
,
E.
,
Hessel
,
V.
, and
Schouten
,
J.
,
2012
, “
Design Methodology for Barrier-Based Two Phases Flow Distributor
,”
AIChE J.
,
58
(
11
), pp.
3482
3493
. 10.1002/aic.13750
26.
Al-Rawashdeh
,
M.
,
Fluitsma
,
L. J. M.
,
Nijhuis
,
T. A.
,
Rebrov
,
E. V.
,
Hessel
,
V.
, and
Schouten
,
J. C.
,
2012
, “
Design Criteria for a Barrier-Based Gas–Liquid Flow Distributor for Parallel Microchannels
,”
Chem. Eng. J.
,
181–182
(
2
), pp.
549
556
. 10.1016/j.cej.2011.11.086
27.
Saad
,
S. B.
,
Clement
,
P.
,
Fourmigue
,
J.
,
Gentric
,
C.
, and
Leclerc
,
J.
,
2012
, “
Single Phase Pressure Drop and Two-Phase Distribution in an Offset Strip Fin Compact Heat Exchanger
,”
Appl. Therm. Eng.
,
49
(
12
), pp.
99
105
. 10.1016/j.applthermaleng.2011.09.022
28.
Saad
,
S. B.
,
Gentric
,
C.
,
Fourmigue
,
J.
,
Clement
,
P.
, and
Leclerc
,
J.
,
2014
, “
CFD and Experimental Investigation of the Gas-Liquid Flow in the Distributor of a Compact Heat Exchanger
,”
Chem. Eng. Res. Des.
,
92
(
11
), pp.
2361
2370
. 10.1016/j.cherd.2014.02.002
29.
Kim
,
S.
,
Choi
,
E.
, and
Cho
,
Y. I.
,
1995
, “
The Effect of Header Shapes on the Flow Distribution in a Manifold for Electronic Packaging Applications
,”
Int. Commun. Heat Mass
,
22
(
3
), pp.
329
341
. 10.1016/0735-1933(95)00024-S
30.
Tondeur
,
D.
, and
Luo
,
L.
,
2004
, “
Design and Scaling Laws of Ramified Fluid Distributors by the Constructal Approach
,”
Chem. Eng. Sci.
,
59
(
8–9
), pp.
1799
1813
. 10.1016/j.ces.2004.01.034
31.
Yuan
,
P.
,
Jiang
,
G. B.
,
He
,
Y. L.
, and
Tao
,
W. Q.
,
2016
, “
Performance Simulation of a Two-Phase Flow Distributor for Plate-fin Heat Exchanger
,”
Appl. Therm. Eng.
,
99
(
4
), pp.
1236
1245
. 10.1016/j.applthermaleng.2016.01.096
32.
Raul
,
A.
,
Bhasme
,
B. N.
, and
Maurya
,
R. S.
,
2016
, “
A Numerical Investigation of Fluid Flow Maldistribution in Inlet Header Configuration of Plate Fin Heat Exchanger
,”
Energy Proc.
,
90
(
12
), pp.
267
275
. 10.1016/j.egypro.2016.11.194
33.
Dario
,
E. R.
,
Tadrist
,
L.
, and
Passos
,
J. C.
,
2013
, “
Review on Two-Phase Flow Distribution in Parallel Channels With Macro and Micro Hydraulic Diameters: Main Results, Analyses, Trends
,”
Appl. Therm. Eng.
,
59
(
1–2
), pp.
316
335
. 10.1016/j.applthermaleng.2013.04.060
You do not currently have access to this content.