https://orcid.org/0000-0002-3001-0512
Abstract
The article considers the schemes of groove arrangement on a partially regular microrelief of type I with coaxial grooves formed on end faces of rotary bodies because of vibration. An analytical dependence was obtained to determine the relative area of a partially regular microrelief depending on the geometrical parameters of the V-shaped grooves. The parameters of the grooves formed at different distances from the center of rotation, with which the relative area of the partially regular microrelief will be the same, are determined. It is found that without adjusting the vibration amplitude of the deforming element, the relative area of the grooves will decrease significantly. The imprint radius of the deforming element and its influence on changes in the relative area of the vibrorolling are also found.
Issue Section:
Technical Notes
References
1.
Revankar
G. D.
, Shetty
R.
, Rao
S. S.
, and Gaitonde
V. N.
, “Analysis of Surface Roughness and Hardness in Ball Burnishing of Titanium Alloy
,” Measurement
58
(December 2014
): 256
–268
, https://doi.org/10.1016/j.measurement.2014.08.0432.
Cao
C.
, Zhu
J.
, and Tanaka
T.
, “Influence of Burnishing Process on Microstructure and Corrosion Properties of Mg Alloy AZ31
,” in International Conference on Advanced Surface Enhancement
, ed. Itoh
S.
and Shukla
S.
(Singapore: Springer, 2020
), 97
–107
, https://doi.org/10.1007/978-981-15-0054-1_113.
Schneider
Y. G.
, Service Properties of Parts with Regular Microrelief
, 2nd ed. (revised and augmented, in Russian) (Leningrad
: Mashinostroenie
, 1982
). 4.
Surfaces with Regular Microshape. Classification, Parameters and Characteristics
, GOST 24773-81 (Moscow
: Izdatelstvo Standartov
, 1988
).5.
Tomanik
E.
, El Mansori
M.
, Souza
R.
, and Profito
F.
, “Effect of Waviness and Roughness on Cylinder Liner Friction
,” Tribology International
120
(April 2018
): 547
–555
, https://doi.org/10.1016/j.triboint.2018.01.0126.
Grützmacher
P. G.
, Profito
F. J.
, and Rosenkranz
A.
, “Multi-Scale Surface Texturing in Tribology—Current Knowledge and Future Perspectives
,” Lubricants
7
, no. 11
(October 2019
): 95
, https://doi.org/10.3390/lubricants71100957.
Mezghani
S.
, Demirci
I.
, Zahouani
H.
, and El Mansori
M.
, “The Effect of Groove Texture Patterns on Piston-Ring Pack Friction
,” Precision Engineering
36
, no. 2
(April 2012
): 210
–217
, https://doi.org/10.1016/j.precisioneng.2011.09.0088.
Schneider
U.
, Steckroth
A.
, Rau
N.
, and Hubner
G.
, “An Approach to the Evaluation of Surface Profiles by Separating Them into Functionally Different Parts
,” Surface Topography
1
(1988
): 71
–83
.9.
Radionenko
O.
, Kindrachuk
M.
, Tisov
O.
, and Kryzhanovskyi
A.
, “Features of Transition Modes of Friction Surfaces with Partially Regular Microrelief
,” Aviation
22
, no. 3
(November 2018
): 86
–92
, https://doi.org/10.3846/aviation.2018.620410.
Pawlus
P.
, Reizer
R.
, and Wieczorowski
M.
, “Reverse Problem in Surface Texture Analysis—One-Process Profile Modeling on the Basis of Measured Two-Process Profile after Machining or Wear
,” Materials
12
, no. 24
(December 2019
): 4169, https://doi.org/10.3390/ma1224416911.
Nanbu
T.
, Ren
N.
, Yasuda
Y.
, Zhu
D.
, and Wang
Q. J.
, “Micro-textures in Concentrated Conformal-Contact Lubrication: Effects of Texture Bottom Shape and Surface Relative Motion
,” Tribology Letters
29
, no. 3
(March 2008
): 241
–252
, https://doi.org/10.1007/s11249-008-9302-912.
Wos
S.
, Koszela
W.
, and Pawlus
P.
, “Comparing Tribological Effects of Various Chevron-Based Surface Textures under Lubricated Unidirectional Sliding
,” Tribology International
146
(June 2020
): 106205, https://doi.org/10.1016/j.triboint.2020.10620513.
Nagîţ
G.
, Slătineanu
L.
, Dodun
O.
, Rîpanu
M.
, and Mihalache
A. M.
, “Surface Layer Microhardness and Roughness after Applying a Vibroburnishing Process
,” Journal of Materials Research and Technology
8
, no. 5
(September–October 2019
): 4333
–4346
, https://doi.org/10.1016/j.jmrt.2019.07.04414.
Slavov
S.
, Dimitrov
D.
, and Iliev
I.
, “Variability of Regular Relief Cells Formed on Complex Functional Surfaces by Simultaneous Five-Axis Ball Burnishing
,” UPB Scientific Bulletin, Series D: Mechanical Engineering
82
, no. 3
(August 2020
): 195
–206
.15.
Slavov
S.
and Iliev
I.
, “Design and FEM Static Analysis of an Instrument for Surface Plastic Deformation of Non-planar Functional Surfaces of Machine Parts
,” Fiability & Durability
1
, no. 2
(November 2016
): 3
–9
. 16.
Gómez-Gras
G.
, Travieso-Rodríguez
J. A.
, González-Rojas
H. A.
, Nápoles-Alberro
A.
, Carrillo
F. J.
, and Dessein
G.
, “Study of a Ball-Burnishing Vibration-Assisted Process
,” Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
229
, no. 1
(April 2014
): 172
–177
, https://doi.org/10.1177/095440541452638317.
Dzyura
V.
, “Modeling of Partially Regular Microreliefs Formed on the End Faces of Rotation Bodies by a Vibration Method
,” Ukranian Journal of Mechanical Engineering and Materials Science
6
, no. 1
(2020
): 30
–38
.18.
Schneider
G.
and Lebedinskiy
G. G.
, “Research of Influence of Oil Capacity of Working Surfaces of Sleeves of Cylinders of Automobile Engines on Their Operability
” (in Russian), in Strengthening-Calibrating and Forming Methods of Processing of Details
(Rostov-on Don: Russia, 1970
), 92
–93
. 19.
Schneider
Y. G.
. Method of decorative processing
. Patent 191382, filed June 21, 1962, and issued January 14, 1967
. 20.
Dzyura
V. O.
, “Determination of the Area of Triangular Grooves of Partially Regular Microrelief Formed on the End Surfaces of Rotating Bodies
” (in Ukrainian), Herald of Khmelnitskyi National University, Technical Sciences
283
, no. 2
(2020
): 62
–67
.
This content is only available via PDF.
All rights reserved. This material may not be reproduced or copied, in whole or part, in any printed, mechanical, electronic, film, or other distribution and storage media, without the written consent of ASTM International.
You do not currently have access to this content.
