Measurements of decompression wave speed in conventional and rich natural gas mixtures following rupture of a high-pressure pipe have been conducted. A high-pressure stainless steel rupture tube (internal and 42 m long) has been constructed and instrumented with 16 high frequency-response pressure transducers mounted very close to the rupture end and along the length of the tube to capture the pressure-time traces of the decompression wave. Tests were conducted for initial pressures of 33–37 MPa-a and a temperature range of . The experimentally determined decompression wave speeds were compared with both GASDECOM and PIPEDECOM predictions with and without nonequilibrium condensation delays at phase crossing. The interception points of the isentropes representing the decompression process with the corresponding phase envelope of each mixture were correlated with the respective plateaus observed in the decompression wave speed profiles. Additionally, speeds of sound in the undisturbed gas mixtures at the initial pressures and temperatures were compared with predictions by five equations of state, namely, BWRS, AGA-8, Peng–Robinson, Soave–Redlich–Kwong, and Groupe Européen de Recherches Gaziéres. The measured gas decompression curves were used to predict the fracture arrest toughness needed to assure fracture control in natural gas pipelines. The rupture tube test results have shown that the Charpy fracture arrest values predicted using GASEDCOM are within (conservative) and −11% (nonconservative) of the rupture tube predicted values. Similarly, PIPEDECOM with no temperature delay provides fracture arrest values that are within and −20% of the rupture tube predicted values, while PIPEDECOM with a temperature delay provides fracture arrest values that are within 0% and −20% of the rupture tube predicted values. Ideally, it would be better if the predicted values by the equations of state were above the rupture tube predicted values to make the predictions conservative but that was not always the case.
Skip Nav Destination
Article navigation
October 2010
Research Papers
Measurement of Decompression Wave Speed in Rich Gas Mixtures at High Pressures (370 bars) Using a Specialized Rupture Tube
J. Geerligs,
J. Geerligs
NOVA Research & Technology Center
, Calgary, AB, Canada, T2E 7K7
Search for other works by this author on:
R. J. Eiber
R. J. Eiber
Consultant Inc.
, Columbus, OH, USA, 43220
Search for other works by this author on:
K. K. Botros
J. Geerligs
NOVA Research & Technology Center
, Calgary, AB, Canada, T2E 7K7
R. J. Eiber
Consultant Inc.
, Columbus, OH, USA, 43220J. Pressure Vessel Technol. Oct 2010, 132(5): 051303 (15 pages)
Published Online: August 31, 2010
Article history
Received:
October 29, 2009
Revised:
February 27, 2010
Online:
August 31, 2010
Published:
August 31, 2010
Citation
Botros, K. K., Geerligs, J., and Eiber, R. J. (August 31, 2010). "Measurement of Decompression Wave Speed in Rich Gas Mixtures at High Pressures (370 bars) Using a Specialized Rupture Tube." ASME. J. Pressure Vessel Technol. October 2010; 132(5): 051303. https://doi.org/10.1115/1.4001438
Download citation file:
Get Email Alerts
Influence of water cover on the blast resistance of circular plates
J. Pressure Vessel Technol
Dynamic response and damage analysis of a large steel tank impacted by an explosive fragment
J. Pressure Vessel Technol
Surface Strain Measurement for Non-Intrusive Internal Pressure Evaluation of A Cannon
J. Pressure Vessel Technol
Related Articles
Effect of Lüders Plateau on Fracture Response and Toughness of Pipelines Subject to Extreme Plastic Bending
J. Pressure Vessel Technol (October,2011)
Measurements of Decompression Wave Speed in Pure Carbon Dioxide and Comparison With Predictions by Equation of State
J. Pressure Vessel Technol (June,2016)
Numerical Investigation of Tearing Fracture of Wrinkled Pipe
J. Offshore Mech. Arct. Eng (February,2010)
A Risk-Informed Approach to Leak-Before-Break Assessment of Pressure Tubes in CANDU Reactors
J. Pressure Vessel Technol (April,2010)
Related Proceedings Papers
Related Chapters
DEVELOPMENTS IN STRAIN-BASED FRACTURE ASSESSMENTS - A PERSPECTIVE
Pipeline Integrity Management Under Geohazard Conditions (PIMG)
Applications of Elastic-Plastic Fracture Mechanics in Section XI, ASME Code Evaluations
Online Companion Guide to the ASME Boiler & Pressure Vessel Codes
Section XI Flaw Acceptance Criteria and Evaluation Using Code Procedures
Online Companion Guide to the ASME Boiler & Pressure Vessel Codes