The concept of leak-before-break (LBB) is often used in safety cases for pressure systems, particularly, in the nuclear industry. An important factor in making a LBB case is in the prediction of the leak rate of fluid through a crack. This paper presents a summary of a program of work, which had the aim of improving guidance on leak rate evaluation for the LBB procedures in the R6 defect assessment methodology. Methods of calculating leak rates have been reviewed, and this has led to a crack morphology model being proposed, which represents single-phase isothermal compressible flow through a crack. In the crack morphology model, the flow is assumed by default to be fully rough turbulent, and the effective roughness to vary between a local roughness value for narrow cracks and a global value (i.e., the overall crack contours) for wide cracks. The effect of pressure drops due to changes in the flow direction at crack turns has also been included. Calculations using the model show that the friction factor relation due to Spence et al. (1991, “Leakage Flow Through Small Cracks—Report of Second Stage of Experimental Work,” unpublished) gives better agreement with measured flow rates than that due to Button et al. (1978, “Gas Flow Through Cracks,” ASME J. Fluids Eng., 100, pp. 453–458), which tends to overestimate the flow rate for the examples studied. The inclusion of an inertial pressure term arising from changes in overall flow direction appears to be justified.
Skip Nav Destination
Article navigation
February 2008
Research Papers
Leak Before Break: Studies in Support of New R6 Guidance on Leak Rate Evaluation
J. P. Taggart,
J. P. Taggart
Serco Assurance
, Birchwood Park, Warrington, Cheshire WA3 6GA, United Kingdom
Search for other works by this author on:
P. J. Budden
P. J. Budden
British Energy Generation Ltd.
, Barnett Way, Barnwood, Gloucestershire GL4 3RS, United Kingdom
Search for other works by this author on:
J. P. Taggart
Serco Assurance
, Birchwood Park, Warrington, Cheshire WA3 6GA, United Kingdom
P. J. Budden
British Energy Generation Ltd.
, Barnett Way, Barnwood, Gloucestershire GL4 3RS, United KingdomJ. Pressure Vessel Technol. Feb 2008, 130(1): 011402 (6 pages)
Published Online: January 17, 2008
Article history
Received:
February 9, 2006
Revised:
December 19, 2006
Published:
January 17, 2008
Citation
Taggart, J. P., and Budden, P. J. (January 17, 2008). "Leak Before Break: Studies in Support of New R6 Guidance on Leak Rate Evaluation." ASME. J. Pressure Vessel Technol. February 2008; 130(1): 011402. https://doi.org/10.1115/1.2826422
Download citation file:
Get Email Alerts
Surface Strain Measurement for Non-Intrusive Internal Pressure Evaluation of a Cannon
J. Pressure Vessel Technol (December 2024)
Dynamic Response and Damage Analysis of a Large Steel Tank Impacted by an Explosive Fragment
J. Pressure Vessel Technol (February 2025)
Related Articles
A Probabilistic Assessment Technique Applied to a Cracked Heat Exchanger Tube Subjected to Flow-Induced Vibration
J. Pressure Vessel Technol (June,2009)
Estimation of Leak Flow Rates Through Narrow Cracks
J. Pressure Vessel Technol (October,2009)
Dynamic Shear Fracture at Subsonic and Transonic Speeds in a Compressible Neo-Hookean Material Under Compressive Prestress
J. Appl. Mech (September,2002)
The Role of Strain Rate Response on Tribological Behavior of
Metals
J. Tribol (January,2013)
Related Proceedings Papers
Related Chapters
Use of Large Standoff Magnetometry for Geohazard Pipeline Integrity Investigations
Pipeline Integrity Management Under Geohazard Conditions (PIMG)
DEVELOPMENTS IN STRAIN-BASED FRACTURE ASSESSMENTS - A PERSPECTIVE
Pipeline Integrity Management Under Geohazard Conditions (PIMG)
Introduction and Definitions
Handbook on Stiffness & Damping in Mechanical Design