Lightweight metal matrix nanocomposites (MMNCs) (metal matrix with nanosized ceramic particles) can be of significance for automobile, aerospace, and numerous other applications. It would be advantageous to develop effective nanomanufacturing methods for fabrication of bulk components of aluminum-based MMNCs through solidification processing. However, it is extremely difficult to disperse nanosized ceramic particles uniformly in molten aluminum. In this paper, a high power ultrasonic probe is used to disperse nanosized SiC particles into molten aluminum alloy A356. Experimental results show that the ultrasonic cavitation based dispersion of nanoparticles in molten aluminum alloy is effective. The uniform nanoparticle dispersion in the Al alloy matrix resulted in significantly improved mechanical properties. To enhance the nanomanufacturing efficiency, various nanoparticle feeding techniques were explored and experimental results are presented.
Skip Nav Destination
e-mail: xcli@cae.wisc.edu
Article navigation
April 2007
Technical Papers
Ultrasonic Cavitation-Based Nanomanufacturing of Bulk Aluminum Matrix Nanocomposites
Yong Yang,
Yong Yang
Department of Mechanical Engineering,
University of Wisconsin-Madison
, 1513 University Avenue, Madison, WI 53706
Search for other works by this author on:
Xiaochun Li
Xiaochun Li
Department of Mechanical Engineering,
e-mail: xcli@cae.wisc.edu
University of Wisconsin-Madison
, 1513 University Avenue, Madison, WI 53706
Search for other works by this author on:
Yong Yang
Department of Mechanical Engineering,
University of Wisconsin-Madison
, 1513 University Avenue, Madison, WI 53706
Xiaochun Li
Department of Mechanical Engineering,
University of Wisconsin-Madison
, 1513 University Avenue, Madison, WI 53706e-mail: xcli@cae.wisc.edu
J. Manuf. Sci. Eng. Apr 2007, 129(2): 252-255 (4 pages)
Published Online: February 5, 2006
Article history
Received:
September 27, 2005
Revised:
February 5, 2006
Citation
Yang, Y., and Li, X. (February 5, 2006). "Ultrasonic Cavitation-Based Nanomanufacturing of Bulk Aluminum Matrix Nanocomposites." ASME. J. Manuf. Sci. Eng. April 2007; 129(2): 252–255. https://doi.org/10.1115/1.2194064
Download citation file:
Get Email Alerts
On-Orbit Processing and Hardware Performance of Microgravity Hydrothermal Synthesis for Graphene Aerogel
J. Manuf. Sci. Eng (December 2024)
A Review on Metallic Drilling Burrs: Geometry, Formation, and Effect on the Mechanical Strength of Metallic Assemblies
J. Manuf. Sci. Eng (April 2025)
Related Articles
Ultrasonic Cavitation Based Nanomanufacturing of Bulk Aluminum Matrix Nanocomposites
J. Manuf. Sci. Eng (June,2007)
Mechanical Properties and Microstructure of Mg ∕ Si C Nanocomposites Fabricated by Ultrasonic Cavitation Based Nanomanufacturing
J. Manuf. Sci. Eng (June,2008)
A Micromechanics-Based Elastoplastic Model for Amorphous Composites With Nanoparticle Interactions
J. Appl. Mech (May,2008)
Solidification of Phase Change Material Nanocomposite Inside a Finned Heat Sink: A Macro Scale Model of Nanoparticles Distribution
J. Thermal Sci. Eng. Appl (August,2019)
Related Proceedings Papers
Related Chapters
Introduction
Bacteriophage T4 Tail Fibers as a Basis for Structured Assemblies
Experimental Studies
Nanoparticles and Brain Tumor Treatment
Conclusions
Bacteriophage T4 Tail Fibers as a Basis for Structured Assemblies