Vacuum insulation panels have values of thermal conductivity that are extremely low ∼4mW/ms˙K compared to the thermal conductivity of most common insulations. Typical ASTM test methods are not designed for testing these very low thermal conductivity materials. An apparatus has been built and tested that uses a thin foil heater and vacuum chamber to test vacuum insulation panels. Several different measurement configurations are studied to determine the effects of the parasitic heat losses. The differences between the ASTM standards and this technique are described and the rationale explained. A new ASTM technique for vacuum panels appears to be needed.

Issue Section:
Conduction
Keywords:
thermal insulation, vacuum insulation, thermal conductivity measurement, heat losses, thermal insulating materials, thermal conductivity
Topics:
ASTM International, Insulation, Temperature, Thermal conductivity, Vacuum, Plates (structures), Uncertainty
1.
Wessling, F. C., Stodieck, L. S., Hoehn, A., Woodard, S., O’Brien, S., and Thomas, S., 2000, “Low Temperature, Low Energy Carrier (LoTec©) and Phase Change Materials (PCMs) for Biological Samples,” 30th International Conference on Environmental Systems, OOICES-338, Toulouse, France, July 10–13, 2000.
2.
Zeng
,
S. Q.
,
Hunt
,
A.
, and
Greif
,
R.
,
1995
, “
Theoretical Modeling of Carbon Content to Minimize Heat Transfer in Silica Aerogel
,”
J. Non-Cryst. Solids
,
186
, pp.
271
–
277
.
3.
ASTM C 117-97, “Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus,” American Society for Testing and Materials, Philadelphia, PA.
4.
Hunt, A. J., Jantzen, K., and Cao, W., 1991, “Aerogel—A High Performance Insulation Material at 0.1 bar,” Insulation Materials: Testing and Applications, ASTM STP 1116, R. S. Graves, and D. C. Wysocki, eds., 2, American Society for Testing and Materials, Philadelphia, pp. 455–463.
5.
ASTM C 518-98, “Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus,” American Society for Testing and Materials, Philadelphia, PA.
6.
ASTM C 745-92, “Standard Test Method for Heat Flux Through Evacuated Insulations Using a Guarded Flat Plate Boiloff Calorimeter,” American Society for Testing and Materials, Philadelphia, PA.
7.
ASTM C 1114-00, “Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus,” American society for Testing and Materials, Philadelphia, PA.
8.
Zeng
,
J. S. Q.
,
Stevens
,
P. C.
,
Hunt
,
A. J.
,
Grief
,
R.
, and
Lee
,
D.
,
1996
, “
Thin-Film-Heater Thermal Conductivity Apparatus and Measurement of Thermal Conductivity of Silica Aerogel
,”
Int. J. Heat Mass Transf.
,
39
(
11
), pp.
2311
–
2317
.
9.
Coleman, H. W., and Steele, W. G., 1999, Experimentation and Uncertainty Analysis for Engineers, 2nd ed., John Wiley & Sons, Inc., New York.
10.
Coleman, H. W., and Steele, W. G., 1999, Experimentation and Uncertainty Analysis for Engineers, 2nd ed., John Wiley & Sons, Inc., New York, p. 50.
11.
Incropera, F. P., and DeWitt, D. P., 1996, Fundamentals of Heat and Mass Transfer, 4th ed., John Wiley & Sons, Inc., New York.
12.
Hewitt, G. F., Shires, G. L., and Polezhaev, Y. V., eds., 1997, International Encyclopedia of Heat and Mass Transfer, CRC Press LLC., Boca Raton FL., p. 1949.
13.
Smith
,
D. M.
,
Maskara
,
A.
, and
Boes
,
U.
,
1998
, “
Aerogel-based Thermal Insulation
,”
J. Non-Cryst. Solids
,
225
, pp.
254
–
259
.
Copyright © 2004
 by ASME
You do not currently have access to this content.