An experimental investigation was performed to determine the heat transfer rates for an impinging free-surface axisymmetric jet of lubricating oil for a wide range of Prandtl numbers (48 to 445) and for conditions of highly varying properties (viscosity ratios up to 14) in the flowing film. Heat transfer coefficients were obtained for jet Reynolds numbers from 109 to 8592, nozzle orifice diameters of 0.51, 0.84 and 1.70 mm and a heated surface diameter of 12.95 mm. The effect of nozzle to surface spacing (1 to 8.5 mm), was also investigated. Viscous dissipation was found to have an effect at low heat fluxes. Distinct heat transfer regimes were identified for initially laminar and turbulent jets. The data show that existing constant property correlations underestimate the heat transfer coefficient by more than 100 percent as the wall to fluid temperature difference increases. Over 700 data points were used to generate Nusselt number correlations which satisfactorily account for the highly varying properties with a mean absolute error of less than ten percent.
Issue Section:
Jets, Wakes, and Impingement
1.
Azuma
T.
Hoshino
T.
1984
a, “The Radial Flow of a Thin Liquid Film. First Report, Laminar-Turbulent Transition
,” Bulletin of the Japanese Society of Mechanical Engineers
, Vol. 27
, No. 234
, pp. 2739
–2746
.2.
Azuma
T.
Hoshino
T.
1984
b, “The Radial Flow of a Thin Liquid Film. Second Report, Liquid Film Thickness
,” Bulletin of the Japanese Society of Mechanical Engineers
, Vol. 27
, No. 234
, pp. 2747
–2754
.3.
Downs, S. J., and James, E. H., 1987, “Jet Impingement Heat Transfer—A Literature Survey,” ASME Paper No. 87-HT-35.
4.
Ellison
B.
Webb
B. W.
1994
, “Local Heat Transfer to Impinging Liquid Jets in the Initially Laminar, Transitional, and Turbulent Regimes
,” International Journal of Heat and Mass Transfer
, Vol. 37
, No. 8
, pp. 1207
–1216
.5.
Ferreira
C. A.
Richter
E.
1993
, “A Detailed Design of a 250 kw Switched Reluctance Starter/generator for an Aircraft Engine
,” SAE Journal of Aerospace
, Vol. 102
, pp. 289
–300
.6.
Gardon, R., and Cobonpue, J., 1961, “Heat Transfer Between a Flat Plate and Jets of Air Impinging on it,” Proceedings of the Second International Heat Transfer Conference, Boulder CO, ASME, New York, pp. 454–460.
7.
Goldstein
R. J.
Behbahani
A. I.
Kieger Heppelmann
K.
1986
, “Streamwise Distribution of the Recovery Factor and the Local Heat Transfer Coefficient to an Impinging Circular Air Jet
,” International Journal of Heal and Mass Transfer
, Vol. 29
, No. 8
, pp. 1227
–1235
.8.
Gu, C. B., Su, G. S., Chow, L. C., and Pais, M. R., 1993, “Comparison of Spray and Jet Impingement Cooling,” ASME Paper No. 93-HT-20.
9.
Jiji, L. M., and Dagan, Z., 1987, “Experimental Investigation of Single Phase Multi-Jet Impingement Cooling of an Array of Microelectronic Heat Sources.” Proceedings of the International Symposium on Cooling Technology, Pacific Institute for Thermal Engineering, pp. 265–283.
10.
Kays, W. M., and Crawford, M. E., 1980, Convective Heat and Mass Transfer, McGraw-Hill, New York, pp. 296–297.
11.
Kline
S. J.
McClintock
F. A.
1953
, “Describing Uncertainties in Single-Sample Experiments
,” Mechanical Engineering
, Vol. 75
, Jan., pp. 3
–8
.12.
Lee
X. C.
Ma
C. F.
Zheng
Q.
Zhuang
Y.
Tian
Y. Q.
1997
, “Numerical Study of Recovery Effect and Impingement Heat Transfer with Submerged Circular Jets of Large Prandtl Number Liquid
,” International Journal of Heat and Mass Transfer
, Vol. 40
, No. 11
, pp. 2647
–2653
.13.
Leland, J. E., 1994, “The Effects of Channel Curvature and Protrusion Height on Nucleate Boiling and the Critical Heat Flux of a Simulated Electronic Chip,” Ph.D. dissertation, University of Kentucky, Lexington, KY.
14.
Liu
X.
Lienhard
V. J. H.
Lombara
J. S.
1991
, “Convective Heat Transfer by Impingement of Circular Liquid Jets
,” ASME JOURNAL OF HEAT TRANSFER
, Vol. 113
, pp. 571
–582
.15.
Livingood, J. N. B., and Hrycak, P., 1973, “Impingement Heat Transfer from Turbulent Air Jets to Flat Plates—A Literature Survey,” NASA TM X-2778.
16.
Ma, C.-F., Sun, H., Auracher, H., and Gomi, T., 1990, “Local Convective Heat Transfer From Vertical Heated Surfaces to Impinging Circular Jets of Large Prandtl Number Liquids,” Proceedings of the 9th International Heat Transfer Conference, Vol. 2, Jerusalem, Hemisphere, Washington, DC, pp. 441–446.
17.
Ma
C. F.
Zheng
Q.
Sun
H.
Wu
K.
1997
a, “Local Characteristics for Impingement Heat Transfer with Oblique Round Free-Surface Jets of Large Prandtl Number Liquid
,” International Journal of Heat and Mass Transfer
, Vol. 40
, No. 10
, pp. 2249
–2259
.18.
Ma
C. F.
Zheng
Q.
Lee
S. C.
Gomi
T.
1997
b, “Impingement Heat Transfer and Recovery Effect with Submerged Jets of Large Prandtl Number Liquid—I. Unconfined Circular Jets
,” International Journal of Heat and Mass Transfer
, Vol. 40
, No. 6
, pp. 1481
–1490
.19.
Ma
C. F.
Zhuang
Y.
Lee
S. C.
Gomi
T.
1997
c, “Impingement Heat Transfer and Recovery Effect with Submerged Jets of Large Prandtl Number Liquid—II. Initially Laminar Confined Slot Jets
,” International Journal of Heat and Mass Transfer
, Vol. 40
, No. 6
, pp. 1491
–1500
.20.
Martin
H.
1977
, “Heat and Mass Transfer Between Impinging Gas Jets and Solid Surfaces
,” Advances in Heat Transfer
, Vol. 13
, Academic Press, New York, pp. 1
–60
.21.
Metzger, D. E., Cummings, K. N., and Ruby, W. A., 1974, “Effects of Prandtl Number on Heat Transfer Characteristics of Impinging Liquid Jets,” Proceedings of the 5th International Heat Transfer Conference, Vol. 2, Tokyo, Hemisphere, Washington, DC, pp. 20–24.
22.
Pais, M. R., Leland, J. E., Chang, W. S., and Chow, L. C, 1993, “Jet Impingement Cooling Using a Jet Fuel,” ASME Paper No. 93-HT-22.
23.
Pais, M. R., Chow, L. C., Knee, J., Bonneau, V., Leland, J. E., and Beam, J. E., 1995, “Jet Impingement Cooling in VSCF Generators,” SAE Paper No. SAE 951451, SAE Aerospace Atlantic Conference, Dayton, OH.
24.
Pan
Y.
Stevens
J.
Webb
B. W.
1992
, “Effect of Nozzle Configuration of Transport in the Stagnation Zone of Axisymmetric, Impinging Free-Surface Liquid Jets: Part 2—Local Heat Transfer
,” ASME JOURNAL OF HEAT TRANSFER
, Vol. 114
, pp. 880
–886
.25.
Polat
S.
Huang
B.
Mujumdar
A. S.
Douglas
W. J. M.
1989
, “Numerical Flow and Heat Transfer Under Impinging Jets: A Review
,” Annual Review of Numerical Fluid Mechanics and Heat Transfer
, Vol. 2
, Hemisphere, New York, pp. 157
–197
.26.
Rahman, M. M., Bula, A. J., and Leland, J. E., 1998, “Numerical Modeling of Conjugate Heat Transfer During Free Liquid Jet Impingement,” Proceedings of the ASME Advanced Energy Systems Division, AES-Vol. 38, ASME, New York, pp. 475–486.
27.
Rahman, M. M., Bula, A. J., and Leland, J. E., 1998, “Conjugate Heat Transfer During Free Jet Impingement of a High Prandtl Number Fluid,” Numerical Heat Transfer, Part A: Applications, submitted for publication.
28.
Wang
X. S.
Dagan
Z.
Jiji
L. M.
1989
, “Conjugate Heat Transfer Between a Laminar Impinging Liquid Jet and a Solid Disk
,” International Journal of Heat and Mass Transfer
, Vol. 32
, No. 11
, pp. 2189
–2197
.29.
Webb
B. W.
Ma
C.-F.
1995
, “Single-Phase Liquid Jet Impingement Heat Transfer
,” Advances in Heat Transfer
, Vol. 26
, Academic Press, New York, pp. 105
–217
.30.
Wolf
D. H.
Incropera
F. P.
Viskanta
R.
1993
, “Jet Impingement Boiling
,” Advances in Heat Transfer
, Vol. 23
, Academic Press, New York, pp. 1
–132
.
This content is only available via PDF.
Copyright © 1999
by The American Society of Mechanical Engineers
You do not currently have access to this content.
