Abstract
This paper presents a method for the robustness analysis of the bladed disk with bounded random mistuning. The robust stability and performance are evaluated by the upper bound of the structured singular value. The robust control model of the bladed disk is established in virtue of linear fractional transformation. The influences of intentional stiffness mistuning in harmonic patterns on the robustness of the mistuned bladed disk are investigated. The numerical results indicate that the robust performance of the mistuned bladed disk could be effectively enhanced by appropriate harmonic intentional mistuning. The proposed method can help us design a bladed disk, which is insensitive to dangerous random mistuning.
Issue Section:
Gas Turbines: Structures and Dynamics
1.
Wang
, J. J.
, Li
, Q. H.
, and Zhu
, Z. G.
, 2000, “Vibratory Localization of Mistuned Bladed Disk Assemblies—A Review
,” Adv. Mech.
0137-3722, 30
(4
), pp. 517
–528
.2.
Petrov
, E. P.
, and Ewins
, D. J.
, 2003, “Analysis of the Worst Mistuning Patterns in Bladed Disk Assemblies
,” ASME J. Turbomach.
0889-504X, 125
(4
), pp. 623
–631
.3.
Slater
, J. C.
, Minkiewicz
, G. R.
, and Blair
, A. J.
, 1999, “Forced Response of Bladed Disk Assemblies—A Survey
,” Shock Vib. Dig.
0583-1024, 31
(1
), pp. 17
–24
.4.
Griffen
, J. H.
, and Hoosac
, T. M.
, 1984, “Model Development and Statistical Investigation of Turbine Blade Mistuning
,” ASME J. Vib., Acoust., Stress, Reliab. Des.
0739-3717, 106
(4
), pp. 204
–210
.5.
Wei
, S. T.
, and Pierre
, C.
, 1988, “Localization Phenomena in Mistuned Assemblies With Cyclic Symmetry, Part I: Free Vibration
,” ASME J. Vib., Acoust., Stress, Reliab. Des.
0739-3717, 110
(4
), pp. 429
–438
.6.
Kruse
M.
, and Pierre
C.
, 1996, “Forced Response of Mistuned Bladed Disks Using Reduced-Order Modeling
,” Paper No. AIAA-96-1545-CP.7.
Bladh
, R.
, Ottarsson
, G.
, and Pierre
, C.
, 1999, “Reduced Order Modeling and Vibration Analysis of Mistuned Bladed Disk Assemblies With Shrouds
,” ASME J. Eng. Gas Turbines Power
0742-4795, 121
, pp. 515
–522
.8.
Lim
S. -H.
, Bladh
R.
, Castanier
M. P.
, Pierre
C.
, 2003, “A Compact, Generalized Component Mode Mistuning Representation for Modeling Bladed Disk Vibration
,” Paper No. AIAA-2003–1545.9.
Yang
, M. -T.
, and Griffin
, J. H.
, 2001, “A Reduced-Order Model of Mistuning Using a Subset of Nominal System Modes
,” ASME J. Eng. Gas Turbines Power
0742-4795, 123
(4
), pp. 893
–900
.10.
Feiner
, D. M.
, and Griffin
, J. H.
, 2002, “A Fundamental Model of Mistuning for a Single Family of Modes
,” ASME J. Turbomach.
0889-504X, 124
(4
), pp. 597
–605
.11.
Ayers
, J. P.
, Feiner
, D. M.
, and Griffin
, J. H.
, 2006, “A Reduced-Order Model for Transient Analysis of Bladed Disk Forced Response
,” ASME J. Turbomach.
0889-504X, 128
(3
), pp. 466
–473
.12.
Petrov
E. P.
, Vitali
R.
, Haftka
R. T.
, 2000, “Optimization of Mistuned Bladed Discs Using Gradient-Based Response Surface Approximations
,” Paper No. AIAA-2000–1522.13.
Petrov
, E. P.
, and Ewins
, D. J.
, 2003, “Analysis of the Worst Mistuning Patterns in Bladed Disk Assemblies
,” ASME J. Turbomach.
0889-504X, 125
(4
), pp. 623
–631
.14.
Choi
, B. -K.
, and Lentz
, J.
, 2003, “Optimization of Intentional Mistuning Patterns for the Reduction of the Forced Response Effects of Unintentional Mistuning: Formulation and Assessment
,” ASME J. Eng. Gas Turbines Power
0742-4795, 125
(1
), pp. 131
–140
.15.
Scarselli
G.
, Lecce
L.
, 2004, “Non Deterministic Approaches for the Evaluation of the Mistune Effects on the Rotor Dynamics
,” Paper No. AIAA-2004–1748.16.
Thompson
, E. A.
, and Bécus
, G. A.
, 1993, “Optimization of Blade Arrangement in a Randomly Mistuned Cascade Using Simulated Annealing
,” Paper No. AIAA-93–2254.17.
Rivas-Guerra
, A. J.
, and Mignolet
, M. P.
, 2003, “Maximum Amplification of Blade Response Due to Mistuning: Localization and Mode Shape Aspects of the Worst Disks
,” ASME J. Turbomach.
0889-504X, 125
(3
), pp. 442
–454
.18.
Kenyon
, J. A.
, Griffin
, J. H.
, and Feiner
, D. M.
, 2003, “Maximum Bladed Disk Forced Response From Distorsion of a Structural Mode
,” ASME J. Turbomach.
0889-504X, 125
(2
), pp. 352
–363
.19.
Kenyon
, J. A.
, 2004, “Maximum Mistuned Bladed Disk Forced Response With Frequency Veering
,” Paper No. AIAA-2004–3753.20.
Rotea
, M.
, and D’Amato
, F.
, 2002, “New Tools for Analysis and Optimization of Mistuned Bladed Disks
,” Paper No. AIAA-2002–4081.21.
Castanier
, M. P.
, and Pierre
, C.
, 1998, “Investigation of the Combined Effects of Intentional Mistuning and Random Mistuning on the Forced Response of Bladed Disks
,” Paper No. AIAA-98–3720.22.
Kenyon
, J. A.
, and Griffin
, J. H.
, 2003, “Forced Response of Turbine Engine Bladed Disks and Sensitivity to Harmonic Mistuning
,” ASME J. Eng. Gas Turbines Power
0742-4795, 125
(1
), pp. 113
–120
.23.
Zhou
, K. M.
, Doyle
, J. C.
, and Glover
, K.
, 1995, Robust and Optimal Control
, Prentice-Hall
, Englewood Cliffs, NJ
.24.
Ferreres
, G.
, Magni
, J. -F.
, and Biannic
, J. -M.
, 2003, “Robustness Analysis of Flexible Structures: Practical Algorithms
,” Int. J. Robust Nonlinear Control
1049-8923, 13
, pp. 715
–733
.25.
Lawrence
, C. T.
, Tits
, A. L.
, and Dooren
, P. V.
, 2000, “A Fast Algorithm for the Computation of an Upper Bound of the μ-Norm
,” Automatica
0005-1098, 36
, pp. 449
–456
.26.
Yao
, J. Y.
, 2006, “Dynamic and Robust Characteristics Analysis of Mistuned Periodic Structures
,” MS thesis, Beihang University, Beijing.Copyright © 2009
by American Society of Mechanical Engineers
You do not currently have access to this content.
