The turbocharged direct injection stoichiometric spark ignition gasoline engine has less than diesel full load brake engine thermal efficiencies and much larger than diesel penalties in brake engine thermal efficiencies reducing the load. This engine has, however, a much better power density, and therefore may operate at much higher brake mean effective pressure (BMEP) values over driving cycles thus reducing the fuel economy penalty of the vehicle. This engine also has the advantage of the very well developed three way catalytic (TWC) converter after treatment to meet future emission regulations. Replacement of fossil gasoline with renewable gasoline-like fuels has major advantages. Ethanol and methanol have larger than gasoline resistance to knock and heat of vaporization, and this ultimately translates in larger than gasoline compression ratio and boost pressure and spark advances closer to maximum brake torque producing better efficiencies both full and part load. For the specific of these novel turbocharged direct injection stoichiometric spark ignition renewable gasoline-like engines coupled to a hybrid-electric power train, the paper considers the option to boost the total fuel conversion efficiency generating both mechanical and electric energy. When the internal combustion engine operates, significant fuel energy is lost in both the exhaust and the coolant. Part of this energy is recovered here by using organic Rankine cycle (ORC) systems fitted to both the exhaust and the coolant, with their expanders driving generators charging the battery of the car. The exhaust and the coolant organic Rankine cycle are effective in increasing the amount of fuel energy converted in usable power over the full range of loads and speeds. The organic Rankine cycle system fitted on the exhaust permits to increase the usable power versus the fuel energy flow rate of a 3.4% on average, with top improvements up to 6.4%. The system is effective particularly at high speeds and loads. The organic Rankine cycle system fitted on the coolant permits to increase the usable power versus the fuel energy flow rate of a 1.7% on average, with top improvements up to 2.8%. The system is effective particularly at low speeds and loads. The two combined organic Rankine cycle systems permit to increase the usable power versus the fuel energy flow rate of a 5.1% on average, with top improvements up to 8.2%.

References

1.
Energy Efficiency and Renewable Energy Office of Vehicle Technologies, 2009, “
FY 2009 Progress Report for Advanced Combustion Engine Research and Development
,” www1.eere.energy.gov/vehiclesandfuels/pdfs/program/2009_adv_combustion_engine.pdf, retrieved October 26, 2011.
2.
www.avl.com/downsizing-downspeeding-gasoline, retrieved October 25, 2011.
3.
Whitaker
,
P.
, 2009, “
Turbocharged Spark Ignited Direct Injection—A Fuel Economy Solution for the US
,”
Presentation given at DEER 2009
, Dearborn, Michigan, August 3–6, www1.eere.energy.gov/vehiclesandfuels/pdfs/deer_2009/session5/deer09_whitaker.pdf, retrieved October 25, 2011.
4.
Beazley
,
R.
, 2009, “
EBDI®—Application of a High BMEP Downsized Spark Ignited Engine
,”
Presentation given at DEER 2009
, Dearborn, Michigan, August 3–6, www1.eere.energy.gov/vehiclesandfuels/pdfs/deer_2009/session5/deer09_beazley.pdf, retrieved October 25, 2011.
5.
Boretti
,
A.
, 2010, “
Analysis of Design of Pure Ethanol Engines
,”
SAE International Powertrains, Fuels and Lubricants Meeting
, Rio de Janeiro, Brazil, May 5–7, SAE Paper No. 2010-01-1453.
6.
Boretti
,
A.
, 2010, “
Performances of a Turbocharged E100 Engine With Direct Injection and Variable Valve Actuation
,”
SAE 2010 Power Trains, Fuels and Lubricants Meeting
, San Diego, CA, October, SAE Paper No. 2010-01-2154.
7.
Boretti
,
A.
, 2010, “Use of Variable Valve Actuation to Control the Load in a Direct Injection, Turbocharged, Spark-Ignition Engine,” SAE 2010 Power trains, Fuels and Lubricants Meeting, San Diego, CA, October, SAE Paper No. 2010-01-2225.
8.
www1.eere.energy.gov/biomass, retrieved October 26, 2011.
9.
www.afdc.energy.gov/afdc/fuels/properties.html, retrieved October 25, 2011.
10.
Nelson
,
C.
, 2008, “
Exhaust Energy Recovery
,”
Presentation given at DEER 2008
, Detroit, MI, August 8, www1.eere.energy.gov/vehiclesandfuels/pdfs/deer_2008/session5/deer08_nelson.pdf, retrieved October 26, 2011.
11.
Nelson
,
C.
, 2006, “
Exhaust Energy Recovery
,”
Presentation given at DEER 2006
, Detroit, MI August 20–24, www1.eere.energy.gov/vehiclesandfuels/pdfs/deer_2006/session6/2006_deer_nelson.pdf, retrieved October 26, 2011.
12.
Regner
,
G.
,
Teng
,
H.
, and
Cowland
,
C.
, 2006, “
A Quantum Leap for Heavy-Duty Truck Engine Efficiency—Hybrid Power System of Diesel and WHR-ORC Engines
,”
Presentation given at DEER 2006
, Detroit, MI, August 20–24, www1.eere.energy.gov/vehiclesandfuels/pdfs/deer_2006/session6/2006_deer_regner.pdf, retrieved October 26, 2011.
13.
Wagner
,
R.
,
Briggs
,
T.
,
Edwards
,
D.
,
Curran
,
S.
,
Nafziger
,
E.
,
Cho
,
K.
,
Singh
,
G.
, and
Howden
,
K.
, 2010, “
Achieving and Demonstrating Vehicle Technologies Engine Fuel Efficiency Milestones
,”
Presentation given at 2010 DOE Vehicle Technologies and Hydrogen Programs Annual Merit Review and Peer Evaluation Meeting
, Washington DC, June 7–11, www1.eere.energy.gov/vehiclesandfuels/pdfs/merit_review_2010/combustion/ace017_wagner_2010_o.pdf, retrieved October 26, 2011.
14.
Cooper
,
D.
,
Baines
,
N.
, and
Sharp
,
N.
, 2010, “
Organic Rankine Cycle Turbine for Exhaust Energy Recovery in a Heavy Truck Engine
,”
Presentation given at DEER 2010
, Detroit, MI, September 27–30, www1.eere.energy.gov/vehiclesandfuels/pdfs/deer_2010/wednesday/presentations/deer10_baines.pdf, retrieved October 26, 2011.
15.
Bianchi
,
M.
, and
De Pascale
,
A.
, 2011, “
Bottoming Cycles for Electric Energy Generation: Parametric Investigation of Available and Innovative Solutions for the Exploitation of Low and Medium Temperature Heat Sources
,”
Appl. Energy
,
88
(
5
), pp.
1500
1509
.
16.
Hueffed
,
A. K.
, and
Mago
,
P. J.
, 2011, “
Energy, Economic, and Environmental Analysis of Combined Heating and Power-Organic Rankine Cycle and Combined Cooling, Heating, and Power-Organic Rankine Cycle Systems
,”
Proc. Inst. Mech. Eng., Part A
,
225
(
1
), pp.
24
32
.
17.
Miller
,
E. W.
,
Hendricks
,
T. J.
,
Wang
,
H.
, and
Peterson
,
R. B.
, 2011, “
Integrated Dual-Cycle Energy Recovery Using Thermoelectric Conversion and an Organic Rankine Bottoming Cycle
,”
Proc. Inst. Mech. Eng., Part A
,
225
(
1
), pp.
33
43
.
18.
Quoilin
,
S.
,
Aumann
,
R.
,
Grill
,
A.
,
Schuster
,
A.
,
Lemort
,
V.
, and
Spliethoff
,
H.
, 2011, “
Dynamic Modeling and Optimal Control Strategy of Waste Heat Recovery Organic Rankine Cycles
,”
Appl. Energy
,
88
(
6
), pp.
2183
2190
.
19.
Roy
,
J. P.
,
Mishra
,
M. K.
, and
Misra
,
A.
, 2010, “
Parametric Optimization and Performance Analysis of a Waste Heat Recovery System Using Organic Rankine Cycle
,”
Energy
,
35
(
12
), pp.
5049
5062
.
20.
Sánchez
,
D.
,
Muñoz De Escalona
,
J. M.
,
Monje
,
B.
,
Chacartegui
,
R.
, and
Sánchez
,
T.
, 2011, “
Preliminary Analysis of Compound Systems Based on High Temperature Fuel Cell, Gas Turbine and Organic Rankine Cycle
,”
J. Power Sources
,
196
(
9
), pp.
4355
4363
.
21.
Gu
,
W.
,
Weng
,
Y.
,
Wang
,
Y.
, and
Zheng
,
B.
, 2009, “
Theoretical and Experimental Investigation of an Organic Rankine Cycle for a Waste Heat Recovery System
,”
Proc. Inst. Mech. Eng., Part A
,
223
(
5
), pp.
523
533
.
22.
Schuster
,
A.
,
Karellas
,
S.
, and
Aumann
,
R.
, 2010, “
Efficiency Optimization Potential in Supercritical Organic Rankine Cycles
,”
Energy
,
35
(
2
), pp.
1033
1039
.
23.
Schuster
,
A.
,
Karellas
,
S.
,
Kakaras
,
E.
, and
Spliethoff
,
H.
, 2009, “
Energetic and Economic Investigation of Organic Rankine Cycle Applications
,”
Appl. Therm. Eng.
,
29
(
8–9
), pp.
1809
1817
.
24.
Weerasinghe
,
W. M. S. R.
,
Stobart
,
R. K.
, and
Hounsham
,
S. M.
, 2010, “
Thermal Efficiency Improvement in High Output Diesel Engines a Comparison of a Rankine Cycle With Turbo-Compounding
,”
Appl. Therm. Eng.
,
30
(
14–15
), pp.
2253
2256
.
25.
www51.honeywell.com/sm/chemicals/refrigerants/eu/en/products-n2/organic-n3/organic-genetron-245fa.html?c=25, retrieved October 25, 2011.
26.
Bradley
,
D.
, 2009, “
Combustion and the Design of Future Engine Fuels
,”
Proc. Inst. Mech. Eng., Part C: J. Mech. Eng. Sci.
,
223
(
12
), pp.
2751
2765
.
27.
Takashi
,
H.
, and
Kimitoshi
,
T.
, 2006, “
Laminar Flame Speeds of Ethanol, n-Heptane, Isooctane Air Mixtures
,”
Student Papers from FISITA 2006 World Conference
. FISITA F2006SC40, www.fisita.com/education/congress/sc06papers/f2006sc40.pdf, retrieved October 26, 2011.
28.
Bromberg
,
L.
,
Cohn
,
D. R.
, and
Heywood
,
J. B.
, 2006, “
Calculations of Knock Suppression in Highly Turbocharged Gasoline/Ethanol Engines Using Direct Ethanol Injection
,” MIT Laboratory for Energy and the Environment Report No. LFEE 2006-001, www.ethanolboost.com/LFEE-2006-01.pdf, retrieved October 26, 2011.
29.
Brusstar
,
M.
, and
Bakenhus
,
M.
, 2006, “
Economical, High-Efficiency Engine Technologies for Alcohol Fuels
,” www.epa.gov/otaq/presentations/epa-fev-isaf-no55.pdf, retrieved October 26, 2011.
30.
West
,
B.
, 2008, “Enhanced Ethanol Engine and Vehicle Efficiency (Agreement 13425),” Paper Presented to the Energy 2008 Office of Vehicle Technologies Annual Merit Review Bethesda, Maryland, February 2008, www1.eere.energy.gov/vehiclesandfuels/pdfs/merit_review_2008/fuels/merit08_west.pdf, retrieved October 26, 2011.
31.
www.ricardo.com/en-gb/Software/Productoffering--description/WAVE1/, retrieved October 26, 2011.
32.
Douaud
,
A. M.
, and
Eyzat
,
P.
, 1978, “Four-Octane-Number Method for Predicting the Anti-Knock Behavior of Fuels and Engines,” SAE Paper No. 780080.
33.
Blizard
,
N. C.
, and
Keck
,
J. C.
, 1974, “Experimental and Theoretical Investigation of Turbulent Burning Model for Internal Combustion Engines,” SAE Paper No. 740191.
34.
Hires
,
S. D.
,
Tabaczynski
,
R. J.
, and
Novak
,
J. M.
, 1978, “The Prediction of Ignition Delay and Combustion Intervals for a Homogeneous Charge, Spark Ignition Engine,” SAE Paper No. 780232.
35.
Tabaczynski
,
R. J.
,
Trinker
,
F. H.
, and
Shannon
,
B. A. S.
, 1980, “
Further Refinement and Validation of a Turbulent Flame Propagation Model for Spark-Ignition Engines
,”
Combust. Flame
,
39
, pp.
111
121
.
36.
Morel
,
T.
,
Rackmil
,
C. I.
,
Keribar
,
R.
, and
Jennings
,
M. J.
, 1988, “Model for Heat Transfer and Combustion in Spark Ignited Engines and its Comparison With Experiments,” SAE Paper No. 880198.
37.
Wahiduzzaman
,
S.
,
Morel
,
T.
, and
Sheard
,
S.
, 1993, “Comparison of Measured and Predicted Combustion Characteristics of a Four-Valve S.I. Engine,” SAE Paper No. 930613.
38.
Morel
,
T.
, and
Keribar
,
R.
, 1985, “A Model for Predicting Spatially and Time Resolved Convective Heat Transfer in Bowl-In-Piston Combustion Chambers,” SAE Paper No. 850204.
39.
Boggs
,
D.
, 2011, “
Application of Synergistic Technologies to Achieve High Levels of Gasoline Engine Downsizing
,” Presentation given at DEER 2011, Detroit, MI, October 3–6, www1.eere.energy.gov/vehiclesandfuels/pdfs/deer_2011/monday/presentations/deer11_boggs.pdf, retrieved December 22, 2011.
40.
Otobe
,
Y.
,
Goto
,
O.
,
Miyano
,
H.
,
Michio
,
K.
,
Aoki
,
A.
, and
Ogawa
,
T.
, 1989, “Honda Formula One Turbo-charged V-6 1.5L Engine,” SAE Paper No. 890877.
41.
Chen
,
S. K.
, and
Flynn
,
P.
, 1965, “Development of a Compression Ignition Research Engine,” SAE Paper No. 650733.
42.
www.gtisoft.com/img/broch/broch_gtcool.pdf, retrieved October 25, 2011.
You do not currently have access to this content.