This paper presents an experimental and numerical investigation into the dynamic response of three-dimensional (3D) orthogonal woven carbon composites undergoing soft impact. Composite beams of two different fiber architectures, varying only by the density of through-thickness reinforcement, were centrally impacted by metallic foam projectiles. Using high-speed photography, the center-point back-face deflection was measured as a function of projectile impulse. Qualitative comparisons are made with a similar unidirectional (UD) laminate material. No visible delamination occurred in orthogonal 3D woven samples, and beam failure was caused by tensile fiber fracture at the gripped ends. This contrasts with UD carbon-fiber laminates, which exhibit a combination of widespread delamination and tensile fracture. Post impact clamped–clamped beam bending tests were undertaken across the range of impact velocities tested to investigate any internal damage within the material. Increasing impact velocity caused a reduction of beam stiffness: this phenomenon was more pronounced in composites with a higher density of through-thickness reinforcement. A three-dimensional finite-element modeling strategy is presented and validated, showing excellent agreement with the experiment in terms of back-face deflection and damage mechanisms. The numerical analyses confirm negligible influence from through-thickness reinforcement in regard to back-face deflection, but show significant reductions in delamination damage propagation. Finite-element modeling was used to demonstrate the significant structural enhancements provided by the through-the-thickness (TTT) weave. The contributions to the field made by this research include the characterization of 3D woven composite materials under high-speed soft impact, and the demonstration of how established finite-element modeling methodologies can be applied to the simulation of orthogonal woven textile composite materials undergoing soft-impact loading.
Skip Nav Destination
Article navigation
December 2015
Research-Article
Dynamic Response of Orthogonal Three-Dimensional Woven Carbon Composite Beams Under Soft Impact
P. Turner,
P. Turner
Centre for Structural Engineering
and Informatics,
Composites Research Group,
Department of Civil Engineering,
Faculty of Engineering,
The University of Nottingham,
University Park,
Nottingham NG7 2RD, UK
and Informatics,
Composites Research Group,
Department of Civil Engineering,
Faculty of Engineering,
The University of Nottingham,
University Park,
Nottingham NG7 2RD, UK
Search for other works by this author on:
T. Liu,
T. Liu
Centre for Structural Engineering
and Informatics,
Composites Research Group,
Department of Civil Engineering,
Faculty of Engineering,
The University of Nottingham,
University Park,
Nottingham NG7 2RD, UK
e-mail: Tao.Liu@nottingham.ac.uk
and Informatics,
Composites Research Group,
Department of Civil Engineering,
Faculty of Engineering,
The University of Nottingham,
University Park,
Nottingham NG7 2RD, UK
e-mail: Tao.Liu@nottingham.ac.uk
Search for other works by this author on:
X. Zeng
X. Zeng
Composites Research Group,
Faculty of Engineering,
The University of Nottingham,
University Park,
Nottingham NG7 2RD, UK
Faculty of Engineering,
The University of Nottingham,
University Park,
Nottingham NG7 2RD, UK
Search for other works by this author on:
P. Turner
Centre for Structural Engineering
and Informatics,
Composites Research Group,
Department of Civil Engineering,
Faculty of Engineering,
The University of Nottingham,
University Park,
Nottingham NG7 2RD, UK
and Informatics,
Composites Research Group,
Department of Civil Engineering,
Faculty of Engineering,
The University of Nottingham,
University Park,
Nottingham NG7 2RD, UK
T. Liu
Centre for Structural Engineering
and Informatics,
Composites Research Group,
Department of Civil Engineering,
Faculty of Engineering,
The University of Nottingham,
University Park,
Nottingham NG7 2RD, UK
e-mail: Tao.Liu@nottingham.ac.uk
and Informatics,
Composites Research Group,
Department of Civil Engineering,
Faculty of Engineering,
The University of Nottingham,
University Park,
Nottingham NG7 2RD, UK
e-mail: Tao.Liu@nottingham.ac.uk
X. Zeng
Composites Research Group,
Faculty of Engineering,
The University of Nottingham,
University Park,
Nottingham NG7 2RD, UK
Faculty of Engineering,
The University of Nottingham,
University Park,
Nottingham NG7 2RD, UK
Contributed by the Applied Mechanics Division of ASME for publication in the JOURNAL OF APPLIED MECHANICS. Manuscript received June 16, 2015; final manuscript received August 24, 2015; published online September 22, 2015. Assoc. Editor: Weinong Chen.
J. Appl. Mech. Dec 2015, 82(12): 121008 (18 pages)
Published Online: September 22, 2015
Article history
Received:
June 16, 2015
Revised:
August 24, 2015
Citation
Turner, P., Liu, T., and Zeng, X. (September 22, 2015). "Dynamic Response of Orthogonal Three-Dimensional Woven Carbon Composite Beams Under Soft Impact." ASME. J. Appl. Mech. December 2015; 82(12): 121008. https://doi.org/10.1115/1.4031455
Download citation file:
Get Email Alerts
Hamiltonian System-Based Symplectic Framework for Analytical Vibration Analysis of Microplates
J. Appl. Mech (December 2024)
Related Articles
Microplane-Triad Model for Elastic and Fracturing Behavior of Woven Composites
J. Appl. Mech (April,2016)
Fatigue Damage Modeling Techniques for Textile Composites: Review and Comparison With Unidirectional Composite Modeling Techniques
Appl. Mech. Rev (March,2015)
Spectral Stiffness Microplane Model for Quasibrittle Composite
Laminates—Part I: Theory
J. Appl. Mech (March,2008)
Response of Resin Transfer Molded (RTM) Composites Under Reversed Cyclic Loading
J. Eng. Mater. Technol (January,1996)
Related Proceedings Papers
Related Chapters
Advances in the Stochastic Modeling of Constitutive Laws at Small and Finite Strains
Advances in Computers and Information in Engineering Research, Volume 2
Introduction and Definitions
Handbook on Stiffness & Damping in Mechanical Design
Response of Thick, Notched Laminates Subjected to Tension-Compression Cyclic Loads
Composite Materials: Fatigue and Fracture